50 models · Grilles, diffusers, louvres
Two independent blade sets, horizontal front and vertical rear, each adjustable to direct the jet in two planes. For sidewall supply, ceiling slot grilles and large spaces.
W 150–1200 × H 150–1200 mm · 104519155CRT-001b
Grille mounted directly on exposed round or spiral duct, with the frame curved to the duct radius. Individually adjustable blades, single or double deflection, optional extractor damper. For supply or return in factories, sports halls and open-ceiling spaces.
W 254–1219 × H 76–305 mm · calculated, not tested
Aluminium oval blades parallel to the width, 20 mm pitch, individually adjustable. For wall or ceiling supply and return where high airflow at low pressure loss is needed.
W 150–1200 × H 150–1200 mm · 104519155CRT-001a
Linear grille with hollow T-bars in extruded aluminium, running parallel to the long side at 20, 16 or 12 mm pitch. Four frame types plus continuous and curved versions; for ceiling, wall or duct mounting, supply (SCLB) or return (SCLB-O).
L 200–3000 × H 45–315 mm · calculated, not tested
Simplified linear bar grille: extruded aluminium frame with welded corners, hollow T-bars at 20, 16 or 12 mm pitch. Flange widths 05/15/25, continuous runs and three curved types; supply, or return SCLB-LS/O (removable core).
W 200–3000 × H 80–600 mm · calculated, not tested
Extruded aluminium return grille with an egg-crate core of 0.35 mm aluminium strip, 12.7 × 12.7 mm cells; 0° or 45° sight-proof core, fixed or removable (SECG-O); round version SECG-R. For high-volume return and extract.
W 200–1250 × H 150–650 mm · calculated, not tested
Supply or return grille with a perforated face panel in an extruded aluminium frame. The flat face screens the ceiling void and is easy to clean; used in schools, hospitals and offices. Fixed face (SPG) or removable face (SPG-O).
W 200–1250 × H 200–1250 mm · calculated, not tested
Return grille with fixed 45° aluminium C-blades in an extruded aluminium frame; the blades hide the view into the plenum. Core on the main frame (SRAG) or in a removable sub-frame (SRAG-O). For general return air in ceilings or walls.
W 250–1250 × H 150–650 mm · calculated, not tested
Round-face return grille in extruded aluminium with fixed 45° C-blades and a round neck for round or flexible duct. For general return and ventilation in walls or ceilings.
Ø 200–600 mm · calculated, not tested
Wall grille with fixed Z-blades carrying a water hook, extruded aluminium frame and blades. For fresh-air intake, exhaust or transfer through walls. Two blade pitches: 50 mm (SWL) and 30 mm (SWL(R)) for rain-exposed positions.
W 200–1000 × H 200–1000 mm · calculated, not tested
Extruded aluminium deflector with curved blades between two side plates, fitted over the discharge face of an air-conditioner outdoor unit to turn hot air down, up, left or right. For tight spaces where discharge air would hit plants, people, windows, doors or walkways.
4540 … 7070 · pending test
Acoustic louver with straight blades at 45°; each blade is a sheet-metal box filled with mineral wool, with a perforated underside. Four depths, 100–300 mm. For generator rooms, cooling towers, plant rooms and factories that need ventilation with noise control.
W 300–1500 × H 600–2400 mm · calculated, not tested
Acoustic sightproof louver with wool-filled V (chevron) blades and a perforated underside; the folded blade blocks direct sight through the louver. Four depths, 100–300 mm. For plant rooms, generators, cooling towers and acoustic enclosures.
W 300–1500 × H 600–2400 mm · calculated, not tested
Sand separator louver with two staggered rows of vertical U-section blades; air turns through the gaps while sand drops into a sloped trough at the base and drains outside. For air intakes in sandy, dusty areas.
W 300–2000 × H 300–3200 mm · calculated, not tested
Large-panel extruded aluminium louver with 20 mm hollow oval blades at 45° and 100 mm pitch in an 80 mm deep frame. For external walls or screens that must ventilate while shading against direct sun.
W 300–3000 × H 300–1500 mm · calculated, not tested
Large-panel extruded aluminium louver with 54° Z-blades carrying two rain hooks at 90 mm pitch. For external walls or free-standing screens that must ventilate while keeping out wind-driven rain.
W 300–3000 × H 300–2400 mm · calculated, not tested
Large-panel extruded aluminium louver with inverted-V blades (90° apex, folded lips) at 75 mm pitch in a 100 mm deep channel frame. Overlapping blades restrict the view through the louver; for plant rooms, equipment yards and ventilated façades.
W 300–3000 × H 300–2400 mm · calculated, not tested
Swirl vanes on pivots, adjustable in angle; suits cooled supply at high airflow and large temperature difference, constant or variable volume. Shallow jet drop allows use in low ceilings. Ceiling or wall mounting.
ØN 200 … ØN 630 · calculated, not tested
Adjustable ball jet nozzle for long-throw supply in large, low-noise spaces such as airports and large lobbies. The cylindrical body ØD slides into round duct of the same size, or mounts on walls and ceilings.
ØC 45 … ØC 323 · calculated, not tested
Multi-cone core of pressed aluminium, 65 mm high in every size, for supply to large spaces. Two faces: FK028 on a square panel, FK004 with a round rim.
Ø300 / ØN Ø150 … Ø800 / ØN Ø600 · calculated, not tested
Ball core with a discharge tube that sweeps through about 40°, delivering air to a target point where ceiling diffusers cannot be fitted: supermarkets, large rooms, assembly halls, auditoriums. Wall or duct-side mounting.
ØG 100 … ØG 225 · calculated, not tested
Swivelling ball core with a thumb-screw volume control at the outlet, no special tools needed. Mounts vertically on walls, horizontally in ceilings or at an angle; suits stages, cinemas and places that are hard to reach with ductwork.
ØG 38.1 … ØG 260.3 · calculated, not tested
Adjustable ball-type jet nozzle carrying heated or cooled air over long distances in large spaces: airports, large lobbies, areas needing constant air movement. Wall, ceiling or duct mounting.
ØC 60 … ØC 165 · calculated, not tested
The core is a flat plaque inside a stepped square frame; air leaves through the perimeter slot in a 360° pattern and the closed face hides the neck. The core sets at two depths for cooling and heating. Round neck ØN.
ØN 145 … ØN 345 · calculated, not tested
Two nested square cones in a stepped frame with a pyramid centre; 360° ceiling-attached discharge. The core sets at two depths for cooling and heating. Round neck ØN.
ØN 145 … ØN 345 · calculated, not tested
Three nested square cones form three concentric slots with 360° discharge. The core sets in two positions: horizontal for cooling, downward for heating. Round neck ØN.
ØN 145 … ØN 345 · calculated, not tested
Face and louvres pressed from a single aluminium sheet with no welds; angled louvres give a four-way, ceiling-attached jet. Flush, surface or lay-in mounting.
300 × 300 (N 150 × 150) … 600 × 600 (N 450 × 450) · calculated, not tested
The core is a single flat disc for a minimal look; horizontal jet along the ceiling with no downdraught. Weld-free core on an X-frame, released by latches for damper access.
Ø300 / ØN 145 … Ø600 / ØN 395 · calculated, not tested
Four concentric round cones on a Ø600 face, horizontal jet along the ceiling for larger airflows. Ceiling cut-out or direct mounting on round duct.
600 / Ø345 … 600 / Ø395 · pending test
Aerodynamic disc on a threaded spindle, raised or lowered to change airflow and pattern (long or wide throw). For supply, return or ventilation; suits extract of humid or greasy air from bathrooms and kitchens.
ØN 95 … ØN 245 · calculated, not tested
A flat round disc on a 600 × 600 square panel that drops into a lay-in grid; horizontal jet along the ceiling with no downdraught. Core on an X-frame, released by latches for damper access.
600 × 600 … 600 × 600 · calculated, not tested
Two concentric round cones on a 600 × 600 square panel for lay-in grids; horizontal jet along the ceiling. Core on an X-frame, released by latches for damper access.
600 × 600 / Ø145 … 600 × 600 / Ø295 · pending test
Concentric rings, each rotatable to change the discharge angle (0° or 30°); high airflow and long throw for tall spaces such as theatres, concert halls, exhibitions and sports halls. Ceiling, wall or direct duct mounting via a spigot.
ØN 145 … ØN 345 · calculated, not tested
Radial swirl vanes give a rotating jet with rapid mixing, so temperature and velocity differences in the occupied zone fall quickly. Round (R) or square (S) face fixed to the plenum by one centre screw; for supply or return.
Ak 0.0088 … Ak 0.0295 · calculated, not tested
Square face with slots in a spiral layout, each with its own deflector behind. Turn the deflectors for even swirl, one-way, two-way, or deep downward throw for heating. For supply or return.
300 × 8 … 600 × 48 · pending test
Multi-cone louver face discharging evenly in four directions with a stable ceiling-attached jet and no draught. Lays into T-bar grids or surface-mounts on flat ceilings.
300 / 450 / 600 mm · 104519155CRT-001c
One to six 20 mm slots, each with two curved pattern controllers: vertical, angled or split discharge. Seamless linear appearance, joinable into continuous runs.
1–6 × 20 / 32 mm · 104519155CRT-001d
Quarter cylinder for a 90° corner; the curved perforated face discharges evenly over 90°. Sits neatly in the room corner without taking usable floor space; inlet from above or below.
Ø600–1000 × 900–1800 mm (11)
Round floor outlet for a pressurised raised floor: a deflector cone under the plate turns the upward flow into a 360° horizontal jet along the floor. Fast mixing brings temperature and velocity down within 1–2 m. The stainless plate is walkable; the dirt basket lifts out from above.
NW 200–250 (2)
Fits a 600 module T-bar ceiling. Cool air falls slowly, follows the interior wall and spreads at floor level. Use where no wall space is left: corridors, perimeters, classrooms.
300–600 × 600–1200 mm (4)
As SDV-T with an added 25 mm heating slot. Cooling: air leaves through the perforated face (displacement). Heating: a changeover damper sends air to the slot for a high-velocity downward jet.
600 × 600–1200 mm (2)
Ceiling displacement diffuser: a baffle and funnel behind the perforated face form a bell-shaped jet, so cool air sinks slowly to the floor and spreads like a floor-standing displacement unit. For rooms with no free wall or floor space, mounting height up to 4 m; round plenum box with side spigot.
NW 300–800 (5)
Model specification clauses for this product line, ready for the consultant's tender documents: view, copy or print. The neutral version names no brand; the Starduct version adds a reference-product block with test report numbers.
Together with the general section: P15 – General requirements for all products
Messages are processed by AI to answer you; please do not enter sensitive information.
